莫文龙,肖艳,马凤云,钟梅,刘景梅,艾沙·努拉洪.球磨时间对浆态床CO甲烷化Ni-Al2O3催化剂性能的影响[J].分子催化,2017,31(4):356-364
球磨时间对浆态床CO甲烷化Ni-Al2O3催化剂性能的影响
Influence of Milling Time on the Performance of Ni-Al2O3 Catalyst for CO Methanation Based on Slurry-bed Reactor
投稿时间:2017-07-16  修订日期:2017-07-20
DOI:
中文关键词:  甲烷化  Ni-Al2O3催化剂  低温固相法  浆态床
英文关键词:methanation  Ni-Al2O3  low temperature solid-state reaction  slurry-bed reactor
基金项目:国家高技术研究发展计划(863计划)项目(2015AA050502);新疆大学自然科学基金项目(BS160221).
作者单位E-mail
莫文龙 煤炭洁净转化与化工过程新疆维吾尔自治区重点实验室 新疆大学化学化工学院, 新疆 乌鲁木齐 830046  
肖艳 煤炭洁净转化与化工过程新疆维吾尔自治区重点实验室 新疆大学化学化工学院, 新疆 乌鲁木齐 830046  
马凤云 煤炭洁净转化与化工过程新疆维吾尔自治区重点实验室 新疆大学化学化工学院, 新疆 乌鲁木齐 830046 ma_fy@126.com 
钟梅 煤炭洁净转化与化工过程新疆维吾尔自治区重点实验室 新疆大学化学化工学院, 新疆 乌鲁木齐 830046  
刘景梅 煤炭洁净转化与化工过程新疆维吾尔自治区重点实验室 新疆大学化学化工学院, 新疆 乌鲁木齐 830046  
艾沙·努拉洪 煤炭洁净转化与化工过程新疆维吾尔自治区重点实验室 新疆大学化学化工学院, 新疆 乌鲁木齐 830046  
摘要点击次数: 1803
全文下载次数: 2935
中文摘要:
      结合行星式球磨机,采用低温固相法制备Ni-Al2O3催化剂,考察了球磨时间对Ni-Al2O3催化剂晶相结构(XRD)、还原特征(H2-TPR)、孔道结构(BET)、粒径分布(PSD)、表面形貌(SEM)和浆态床CO甲烷化性能的影响.结果表明,球磨时间为60 min,催化剂(CT-60)平均粒径最小,为141 nm;比表面积最大,为329 m2/g.随球磨时间延长,Ni-Al2O3催化剂的甲烷化性能(CO转化率、CH4选择性和CH4收率)均先增加后减少.其中,球磨时间为60 min制备的催化剂(CT-60)甲烷化性能最佳,其CO转化率、CH4选择性和CH4收率分别达87.9%、86.8%和74.3%.结合催化剂表征可知,CT-60优异的性能与其具有较小的颗粒尺寸(141 nm)和较大的比表面积(329 m2·g-1)有很大的关联.即,催化剂颗粒尺寸越小,比表面积越大,其性能越好.
英文摘要:
      With planetary ball mill, the low temperature solid-state reaction method was used to prepare catalyst. The influence of milling time on the crystal structure (XRD), reduction performance (H2-TPR), pore structure (BET), particle size distribution (PSD), surface morphology (SEM) and CO methanation performance in slurry bed was investigated in this paper. Results showed that, at the milling time of 60 min, the average particle size of the catalyst (CT-60) was only about 141 nm, and the specific surface area was up to 329 m2/g. With the extension of milling time, the methanation performance (CO conversion, CH4 selectivity and CH4 yield) of the Ni-Al2O3 ca-talyst (CT-60) was increased firstly and then decreased as the milling time over 60 min. That is, the CT-60 catalyst prepared at the milling time of 60 min presented the best methanation performance, with CO conversion, CH4 selectivity and CH4 yield of 87.9%, 86.8% and 74.3% respectively. The excellent performance of CT-60 was strongly correlated with its small particle size (141 nm) and its specific surface area (329 m2·g-1). That is, the smaller the particle size of the catalyst, the larger the specific surface area, the better the performance.
HTML  查看全文  查看/发表评论  下载PDF阅读器